Drawer-ing To A Close ~ Kitchen Cabinets Are Done!

In my last post, I made and hung the kitchen cabinet doors. This time, I focused on the drawers. Now with the drawers completed, the kitchen install is drawing to a close!

I started with the drawer boards thickness-planed to 5/8″, and I cut them to a width that would allow for good spacing on the dovetails. I measured and cut all the drawer pieces to length and started making the dovetail corner joints. Here are two boards in the dovetail jig:

P1030261-001

One of the fronts/backs is clamped into the jig horizontally and one of the sides is clamped into the jig vertically. Then the dovetails are cut with a tapered bit in the router.

P1030262-001 After I cut all the dovetails, I took the boards to the table saw and cut a one-blade-wide cut at the bottom of the pieces. This allowed me to slide the aluminum drawer bottoms into place. Here is a set of boards all ready for assembly:

P1030260-001

I cut the aluminum sheets to drawer-bottom size. Then with a small paintbrush, I applied carpenter’s wood glue to the joints and tapped the pieces together with a rubber mallet. With this joint, no nails or screws are needed — a good thing in a tropical climate because any moisture left in the wood will rust nails and screws in short order. Here is the stack of drawers waiting overnight for final sanding of the joints:

P1030264-001

I like kitchen cabinets that have pull-out trays at the bottom of the cabinets because it it is much easier to reach the pan in the back of the cabinet. So I made trays in the same style as the drawers. Here are the trays waiting for sanding:

P1030277-001

Same as the doors, after a good sanding, I gave all the drawers and trays a coat of sanding sealer and two coats of polyurethane, sanding between the coats. The drawers (not the bottom trays) also needed additional drawer fronts so I made and finished those too. Finally it was time to put the drawers and trays into the cabinets. Here are some photos of the completed kitchen:

P1030283-001

The Caoba (African Mahogany) will continue to darken over time and will develop a deep rich red-brown patina. There’s a strip of LED lights behind the sink for a gentle-on-the-eyes light in the middle of the night. Shown here, the light is reflecting off the shine of the waxed concrete countertop.

P1030278-001

P1030282-001

Cat BobBob needs a place to eat, too. I still have to install an LED light strip under the counter here plus caulk the corners of the aluminum.

P1030281-001

This is the baking island — it is two-inches lower than the other cabinets which is especially useful when rolling out dough. It’s an easy-0n-the-back height.

Here is a closeup of a drawer with its attached front, one of the trays, and a door:

P1030284-001

I used the same aluminum floor-plate that I used for the cabinet sides and shelves throughout the house. Termites don’t like aluminum, but they would do a job on plywood drawer bottoms. On the underside of the drawers, I ran beads of urethane caulk to keep the aluminum from rattling.

Here is a closeup of one of the dovetail joints:

P1030285-001

I used Blum brand drawer slides for the drawers and trays. These slides are very nice — when you close a drawer, just push on the drawer, and at the final two-inches you can let go of the drawer and the drawer slide takes over and automatically and silently glides the drawer to its closed position. Here is a short video that I found on YouTube by Dan Lake that shows how the drawers come to a smooth and quiet closed position:

I have to say that I am very, very happy with how the kitchen turned out. Everything looks just right and my eyes are doing a happy dance. Cynthia likes it too, I just wish that there weren’t so many conflicting priorities with the house and that I could have done the kitchen a lot sooner. I still have a couple finishing details, but I’m calling the kitchen, DONE.

Not much in other news this post, except that one day, using bananas from our back yard, Cynthia made “good for you Fun Food” or baked banana bread doughnuts. Gluten-free and very delicious. I couldn’t eat just one!

P1030276-001

Living in Latin America, it doesn’t take long before one comes across a statue or park named for a hero from distant history. Who are they and what did they do? I just finished reading the book, Bolivar: American Liberator by Marie Arana. Almost every night for a couple weeks, I would retire to the screened-in bump out in the master bedroom and read the Kindle version on my smartphone. I enjoyed the hooting of owls as I read.

Over the course of twenty-some years, Bolivar traveled 75,000 miles on horseback, fought the Spanish plus many competing forces withing South America. He made and lost fortunes and always fought for equal representation for all South Americans including freeing slaves. All this was at the same time as Washington and Jefferson and other North American patriots were fighting for freedom. It was a fascinating read.

That’s all for now. Thanks for stopping by.